Doors with PVC Impact Protection

In some environments, namely Hospitals, where you may have high traffic areas or where the doors are likely to get a bit more abuse than normal, there are options available to make the doors last longer, and to make them suitable for the situation they’re in.

 

We have recently manufactured all the doors in the following pictures which have been installed into part of a newly refurbished Fracture Clinic at the William Harvey Hospital.

 

All the doors are a crown cut American White Oak veneer finished in our standard antibacterial water based polish. Here the same pair of doors are shown before and after the door face protection has been fitted.

 

IMG_1771          IMG_1794

 

The door edge protectors completely encapsulate the door edge offering complete protection. The dark Grey groove shown up the edge of the edge protector is the groove for the intumescent strips for the doors FD30 rating.

 

IMG_1792          IMG_1802

 

There are many colours available for the PVC protection, colours can also be split on different side of the doors. The below pair of FD60 doors, was required to be the Light Blue on one face and Burgundy on the other.

 

IMG_1805          IMG_1807

 

All the frames for these doors were supplied with White PVC sections to clad the frames upon installation to offer the same resistance against impact.

 

IMG_1866          IMG_1867

 

IMG_1868          IMG_1869

 

Door stops and architraves are clad in their own White PVC sections which fit around easily to make onsite installation straight forward.

 

IMG_1797           IMG_1800

 

IMG_1810           IMG_1808

 

Give us a call or send over an enquiry to see how we can help with doors for an environment which may require that extra protection.

Bespoke Front Doors

All of our bespoke front doors are manufactured to the individual homeowners requirements. Most people know the sort of design they would like or have seen something somewhere they would like to replicate, some don’t know where to start but just know they want a new one! We can take your ideas and any specification you might have and help to make it a reality.

 

We can utilise a wide variety of timbers and different products to help achieve the look you are after. This can incorporate glazing in the door as well as side lights in the frame, as shown in some of the photos;

 

The below door had the external face clad in Accoya TG+V Boarding, which was then painted.

 

IMG_0734               IMG_0743

 

IMG_0774               photo 1

 

Bespoke front doors manufactured from a solid timber i.e. solid Oak, can be a wide combination of different styles as shown below. They all suit different settings.

 

Joinery 2               Joinery 1

 

Joinery 32               photo 5

 

If a clear finish isn’t something you are after then external doors can be fully finished to any RAL paint colour, for example you may have other timber work or metal work on the front of your house which you’d like the door to match, which was the case for this front door set.

 

IMG_0904               Photo 2

 

IMG_0924               IMG_0912

 

It all starts with your idea, if you’d like us to supply you with a quotation for a new bespoke front door, or any internal doors, please do not hesitate to get in touch with our team.

 

The use of Ironmongery on Fire Doors

Firstly, Ironmongery can only be used on a fire door if the global assessment that the door has been manufactured to stipulates it can be used, or it’ll say something like it can be fitted ‘providing the product has demonstrated contribution to the required integrity performance of this type of doorset’

 

Shockingly, we see it time and time again where ironmongery items are specified for use in fire doors that are not up to standard, and may not even have fire test evidence!

 

Just because an Ironmongery supplier has told you that the hinges, locks, flush bolts etc. are fire rated, you cannot take this as being correct.

 

For this reason alone, we would strongly recommend you do not take the advice from an ironmongery supplier about what can and cannot be used. You should contact your door manufacturer who will be able to check the global assessments that your doors are being manufactured under and give you the correct answer.

 

For example, take a mortice and tenon constructed panel door, which are some of the doors we can manufacture up to an FD60 rating. In the certificate for these doors it specifically states;

 

‘Concealed head mounted closers are not acceptable for the use with this door design since they remove a substantial portion of the head rail and weaken the mortice and tenon joint’

 

However, you can purchase concealed head mounted closers that have been fire tested, so it wouldn’t be unreasonable for someone to think that one could be used in this door construction, but clearly the certification states that it cannot be used so if one were to be installed then the chances are that this door would now fail in a fire.

 

This was a real example and was quite clear that these closers had been installed on many of this type of door, incorrectly, and it was only when we where asked to install some that we brought this to the attention of the installers.

 

A fire resisting doorset without correctly specified or fitted Ironmongery will not perform in a fire they way it should, so make sure you check with the door manufacturer before you next install Ironmongery on a fire door. Its not something that should be over looked.

 

 

Glazed Panel Doors

We have recently completed the supply of over 40 new solid and glazed panel doors to a client based in Edgbaston, Birmingham.

 

IMG_1465

 

We were involved in the project from a very early stage, which helps get the initial designs underway as we will advise what can and can’t be achieved, which is vitally important, especially when the majority of these doors were fire rated to FD30.

 

IMG_1467

 

All doors were required to be fitted with an auto drop-down seal (which is why all the doors in the photos are upside down to protect the fitted seals).

 

IMG_1468

 

The doors are a Softwood construction with a simple Ovolo moulding and matching Ovolo glazing bead.

 

IMG_1470

 

Being involved with the architect from the start ensures the correct products are specified from the off, so there are less snags on the way to the finished product.

Rochester Cathedral.

We have recently completed a project to supply new doors to a wall of internal cupboards at Rochester Cathedral.

 

_q2a6253

 

The doors are a Crown Cut American White Oak veneer, specially made up to mimic a stile and rail door design.

 

_q2a6243

 

The groove detail in the faces of the doors are grooved into solid pieces of American White Oak which are pre-grooved into the doors before the veneering process takes place.

 

_q2a6246

 

All of the doors were finishing in our standard 30% sheen antibacterial water based polish.

 

_q2a6236

 

The end result being a very satisfied customer!

Fire Doors – A Real Life Example

When a fire breaks out within a building the consequences could potentially be devastating. What if that fire has broken out in a densely populated building like a school or hospital.

 

The costs involved can be huge, but not only in fire damage, someone could pay the ultimate price because you haven’t installed third party certificated fire doors.

 

We supplied doors to a project at a hospital refurbishment and shortly after completion a fire broke out in the wing. Nobody was hurt in the fire and the fire was safely put out by the emergency services, and as you can see below, the doors we manufactured stood up to the fire and halted the passage so the fire couldn’t spread.

 

As you can see, this photo shows the side the fire could not get.

 

No1

 

This is the inside of the same door! Fair to say it’s done it’s duty.

 

No3

 

Another photo showing the inside of a different door in the ward, well charred!

 

Picture 101

 

 

Picture 102

 

These photos show the importance of fire doors, correctly manufactured fire doors.

 

Remember the ONLY way to be sure a fire door will perform is to purchase third party certificated fire doors.

 

Give us a call today to see how we can help.

 

A New Project – Panel Doors in a Listed Building.

A recently completed project, Kent Flush Doors supplied all the fire rated panel doors, frames and architraves to high end apartments in the centre of London.

IMG_0809

IMG_0814

The Buildings were listed and so sizes and profiles of existing mouldings and architraves had to match exactly onto all of the new doors and joinery items.

IMG_0811

As well as the internal and external doors (seen in the above image), we also supplied joinery items like the below curved headed arch way between two rooms.

IMG_0816

IMG_0818

The combination of the traditional looking doors and joinery with very clean and simple finishes gave a very modern feel to these apartments.

IMG_0808

Take a look at our Portfolio to view the other similar products we can manufacture, and get in touch to see how we can help.

Third Party Certification – Why is it important?

Why purchase from a manufacturer with a third party certification?

When it comes to the manufacture of fire doors, it is paramount that no corners are cut and every process in production is carried out in the correct way. If any processes are missed, or incorrect products used then you cannot be 100% sure that the door will halt the passage of fire and could well fail, which in turn could be fatal.

 

What does holding a third party certification mean?

We are fully certified BM-TRADA Q-MARK fire door manufacturers and as such our manufacturing processes are audited annually from start to finish to ensure every process is correct and that our doors are being manufactured the same way every single time following the fire certifications.

 

As part of the Q-MARK accreditation we have a fire test on one of the doors we manufacture, which is selected by BM-TRADA, and is carried out every 3 years, and so far none of the doors we have had tested have ever failed.

 

If you are purchasing fire doors from someone who does not have a third party certification, it is a risk, because nobody is monitoring their processes, nobody is telling them what they are doing wrong and more importantly they could well be selling doors which will not perform in a fire – is it really worth the risk?

 

Third party certification gives the responsible person purchasing fire doors and the end user peace of mind that the product will stand up to performance.